Water-stop tie rod
water barrier tie rod
The middle rod stays cast into the wall with a welded water stop; the two outer rods come back off the formwork. The part that remains is the part that seals.
Ask for → diameter, wall thickness, L
Water-stop tie rods · Formwork tie rods · Accessories
Tie rods and formwork hardware, straight from the Yongnian cluster.
We run our own production lines in Yongnian, Hebei — the district that supplies most Chinese fastener exporters. There is no trading layer between our floor and your container.
M12–M32Thread range
3-pieceWater-stop type
Heat no.Recorded per lot
Water-stop · 3-piece
Through-wall · full thread
Wing nut · 2 & 3 wing
Wing plate · stamped
Self-drilling · screws
Drywall · screws
01 / Products
Six lines we produce in-house.
Each line is made on our own equipment in Yongnian, not bought in for resale. Tell us the diameter, the length and the standard — or send a drawing and we will confirm what we can hold to before you commit to an order.
Through-wall tie rod
formwork tie rod
Full-thread rod for wall formwork, supplied in standard lengths or cut to your schedule. Wing nuts and plates are matched to the same thread as the rod.
Ask for → thread, cut length, end finish
Wing nut
combination wing nut · 2 & 3 wing
Two-wing and three-wing patterns, tapped to match the tie rod thread so the assembly pulls square against the waler under load.
Ask for → thread size, wing pattern
Wing plate
formwork wing plate · single piece
Single-piece stamped plate for the waler side of the assembly. A plate is not a nut — the two are supplied as separate items and specified separately.
Ask for → hole size, plate thickness
Self-drilling screw
self-drilling · drill point
Drill point cuts its own hole through light steel and timber, so the fixing goes in one pass without a pre-drilled pilot.
Ask for → diameter, length, coating
Drywall screw
drywall · bugle head
Bugle head seats flush without tearing the board face. Fine and coarse thread, phosphated or galvanised, packed to your count.
Ask for → thread type, length, finish
/ 01
No trading layer
Rods, nuts and plates are produced on our own lines. The margin you are quoted is the factory margin, not a reseller’s markup on top of it.
/ 02
Heat number to container
Every heat number is recorded and matched to the test report that ships with the container, so a lot can be traced back to the coil it came from.
/ 03
Stock in Southeast Asia
Stock is held in our Vietnam and Thailand warehouses, which shortens lead time for buyers in the region instead of waiting on a full production run.
/ 04
Made to your drawing
Send the drawing or the standard you work to. We confirm in writing what we can hold and what we cannot before the order is placed, not after.
02 / Quality
We list only what can be checked.
Certificates and tolerances are confirmed per order, in writing. This page does not carry badges we have not earned — if a claim cannot be verified on your side, it does not belong here.
If your project specifies EN 74, IS 1367 or a national standard, tell us which one. We will confirm what we can certify and what we cannot — before you place the order.
What ships with the goods: a test report matched to the heat number of the lot, and marking and packing to your requirement — neutral, your brand, or ours.
Inspection: third-party inspection of a running order is welcome. You or your agent are free to book it against our production schedule.
Samples: a sample can be arranged against a specific size and standard, so what you approve is what gets run.
03 / Factory
On the floor in Yongnian.
Yongnian District in Handan is the cluster that supplies most Chinese fastener exporters. Being inside it is why our raw material, heat treatment and coating are all within reach of the same road.
- Location
- Cluster
- Type
- Stock points
- Contact
No. 88 Yingbin Road
Yongnian District, Handan
Hebei 057150, China
Yongnian District, Handan
Hebei 057150, China
Yongnian — China’s fastener production base
Source factory, not a trading company
Vietnam · ThailandHeld for Southeast Asian buyers
Robert — export sales
04 / Contact
Tell us the diameter, the length and the standard.
Send those three lines and we will come back with a price, a lead time and a straight answer on what we can hold to. A drawing works too.
WhatsApp
+86 181 3296 8898WeChat on the same number
Address
No. 88 Yingbin Road
Yongnian District, Handan
Hebei 057150, China
Yongnian District, Handan
Hebei 057150, China
Hours
Mon–Sat, 08:00–18:00 (GMT+8)Replies outside these hours usually follow within a day
Origin
Hebei, China